N900 USB networking - Revision history

imported_>rsquared: /* Automatic configuration with Ubuntu 12.04 */

2014-08-04T14:33:20Z

Automatic configuration with Ubuntu 12.04

← Older revision		Revision as of 14:33, 4 August 2014
Line 252:		Line 252:

	ifconfig n900		ifconfig n900

			=== Automatic configuration with Ubuntu 12.04 ===

			Create the file /etc/udev/rules.d/nokia-n900.rules and add this (single) line:
			<pre>
			ACTION=="add", DRIVERS=="usb", ATTRS{idVendor}=="0421", ATTRS{idProduct}=="01c8", ATTRS{manufacturer}=="Nokia", ATTRS{product}=="N900 (PC-Suite Mode)", NAME="usb0", RUN+="/sbin/ifup usb0"
			</pre>

			NetworkManager must be told to ignore usb0. Use ifconfig to get the MAC address of usb0, and add these lines to /etc/NetworkManager/NetworkManager.conf:
			<pre>
			[keyfile]
			unmanaged-devices=mac:XX:XX:XX:XX:XX:XX # replace X's with usb0 MAC address
			</pre>

			Add the following lines to /etc/network/interfaces:
			<pre>
			# N900 on usb0
			allow-hotplug usb0
			iface usb0 inet static
			address 192.168.2.14
			netmask 255.255.255.0
			</pre>

			Restart the affected services:
			<pre>
			sudo service udev restart
			sudo service network-manager restart
			</pre>

			Now when you connect the N900 via USB and select PC Suite Mode, usb0 will be up and configured.

	=== Automatic configuration with Ubuntu 9.10/10.04/11.10 ===		=== Automatic configuration with Ubuntu 9.10/10.04/11.10 ===

imported_>xkr47: /* Starting USB network mode with Windows */ Added note that pcsuite-enable is called by ke-recv

2013-09-08T12:12:39Z

Starting USB network mode with Windows: Added note that pcsuite-enable is called by ke-recv

← Older revision		Revision as of 12:12, 8 September 2013
Line 137:		Line 137:
	</li>		</li>
	<li>		<li>
	Add the following lines to <code>/usr/sbin/pcsuite-enable.sh</code> (Do not forget to change the ip address so it matches the one configured on your host's usb port.)		Add the following lines to <code>/usr/sbin/pcsuite-enable.sh</code> (Do not forget to change the ip address so it matches the one configured on your host's usb port.) (pcsuite-enable.sh is called by the ke-recv which handles memory card mounting, USB mass storage logic, and some other things, based on HAL.)
	<pre>		<pre>
	run-standalone.sh dbus-send --type=method_call --system --dest=com.nokia.icd /com/nokia/icd com.nokia.icd.connect string:DUMMY uint32:0		run-standalone.sh dbus-send --type=method_call --system --dest=com.nokia.icd /com/nokia/icd com.nokia.icd.connect string:DUMMY uint32:0

imported_>joerg_rw at 03:39, 10 March 2013

2013-03-10T03:39:25Z

← Older revision		Revision as of 03:39, 10 March 2013
Line 1:		Line 1:
	This page describes how to enable Networking on the [[Nokia N900\|N900]] via [[USB]], '''to share your PC's internet to N900 via USB'''. The first part describes how to configure the N900. The second part describes how to configure various PC platforms to share internet. This article is based on the [[USB networking\|Maemo 4.x USB networking article]]. It is also possible to use the N900 as a [[N900 USB router\|USB router]].		This page describes how to enable Networking on the [[Nokia N900\|N900]] via [[USB]], '''to share your PC's internet to N900 via USB'''. The first part describes how to configure the N900. The second part describes how to configure various PC platforms to share internet. This article is based on the [[USB networking\|Maemo 4.x USB networking article]]. It is also possible to use the N900 as a [[N900 USB router\|USB router]], to share N900 internet to PC.

	You might want to use the N900 as a USB network device to log into your N900 remotely, or to transfer data from your N900 to another computer, in a situation where wifi or Bluetooth are not an option. If you wish to connect your N900 to a Linux machine over TCP/IP, the [http://maemo.org/development/documentation/pc_connectivity/ PC connectivity] section in the Maemo SDK documentation also contains useful information.		You might want to use the N900 as a USB network device to log into your N900 remotely, or to transfer data from your N900 to another computer, in a situation where wifi or Bluetooth are not an option. If you wish to connect your N900 to a Linux machine over TCP/IP, the [http://maemo.org/development/documentation/pc_connectivity/ PC connectivity] section in the Maemo SDK documentation also contains useful information.

imported_>joerg_rw: edits to make clear this is NOT N900 as NIC

2013-03-10T03:22:02Z

edits to make clear this is NOT N900 as NIC

← Older revision		Revision as of 03:22, 10 March 2013
Line 1:		Line 1:
	This page describes how to enable Networking on the [[Nokia N900\|N900]] via [[USB]]. The first part describes how to configure the N900 ~~as a USB pluggable network device~~. The second part describes how to configure various platforms to ~~use the Nokia N900 as a network device~~. This article is based on the [[USB networking\|Maemo 4.x USB networking article]]. It is also possible to use the N900 as a [[N900 USB router\|USB router]].		This page describes how to enable Networking on the [[Nokia N900\|N900]] via [[USB]], '''to share your PC's internet to N900 via USB'''. The first part describes how to configure the N900. The second part describes how to configure various PC platforms to share internet. This article is based on the [[USB networking\|Maemo 4.x USB networking article]]. It is also possible to use the N900 as a [[N900 USB router\|USB router]].

	You might want to use the N900 as a USB network device to log into your N900 remotely, or to transfer data from your N900 to another computer, in a situation where wifi or Bluetooth are not an option. If you wish to connect your N900 to a Linux machine over TCP/IP, the [http://maemo.org/development/documentation/pc_connectivity/ PC connectivity] section in the Maemo SDK documentation also contains useful information.		You might want to use the N900 as a USB network device to log into your N900 remotely, or to transfer data from your N900 to another computer, in a situation where wifi or Bluetooth are not an option. If you wish to connect your N900 to a Linux machine over TCP/IP, the [http://maemo.org/development/documentation/pc_connectivity/ PC connectivity] section in the Maemo SDK documentation also contains useful information.

131.188.34.118: /* Starting USB network mode */

2013-02-27T23:02:47Z

Starting USB network mode

← Older revision		Revision as of 23:02, 27 February 2013
Line 71:		Line 71:
	</pre>		</pre>

	To automatically setup usb0 when entering PC suite mode ~~change~~ the ~~last few lines of~~ <code>/~~usr~~/~~sbin~~/~~pcsuite-enable.sh~~</code> ~~by adding~~ the ~~"ifup usb0" line.~~		To automatically setup usb0 when entering PC suite mode edit the file <code>/etc/default/usbnetwork</code> and set the variable <code>USBNETWORK_ENABLE</code>.
	<~~pre~~>
	~~logger "$0: sent SIGUSR1 to syncd"~~
	~~ifup usb0~~
	~~exit 0~~
	</~~pre~~>

	~~And, to automatically down your usb0 interface when leaving PC suite mode, add to <code>/usr/sbin/pcsuite-disable.sh</code>~~
	<pre>		<pre>
	~~ifdown usb0~~		# Automatically enable USB network when PC Suite mode is active (default disabled)
	~~exit 0~~		USBNETWORK_ENABLE=1
	</pre>		</pre>

195.96.90.184: /* Automatic configuration with Ubuntu 9.10/10.04/11.10 */

2011-12-01T07:07:07Z

Automatic configuration with Ubuntu 9.10/10.04/11.10

← Older revision		Revision as of 07:07, 1 December 2011
Line 279:		Line 279:
	</pre>		</pre>

	For 11.10, put these lines to /etc/udev/rules.d/99-nokia-n900.rules		<strong>For Ubuntu 11.10</strong>, put these lines to /etc/udev/rules.d/99-nokia-n900.rules
	<pre>		<pre>
	SUBSYSTEM=="net", ACTION=="add", ATTRS{idVendor}=="0421", ATTRS{idProduct}=="01c8", ATTRS{manufacturer}=="Nokia", ATTRS{product}=="N900 (PC-Suite Mode)", NAME="usb0", RUN+="/sbin/ifconfig usb0 192.168.2.14 up"		SUBSYSTEM=="net", ACTION=="add", ATTRS{idVendor}=="0421", ATTRS{idProduct}=="01c8", ATTRS{manufacturer}=="Nokia", ATTRS{product}=="N900 (PC-Suite Mode)", NAME="usb0", RUN+="/sbin/ifconfig usb0 192.168.2.14 up", RUN+="/sbin/iptables -A POSTROUTING -t nat -s 192.168.2.15/32 -j MASQUERADE"
			</pre>
			and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration". But for forwarding you should add to <code>/etc/sysctl.conf</code>
			<pre>
			net.ipv4.ip_forward=1
	</pre>		</pre>
	~~and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration".~~

	The Network Manager on Ubuntu 11.10 won't auto detect this <code>usb0</code> interface, you will have to check it via <code>ping</code> or via Network Tools.		The Network Manager on Ubuntu 11.10 won't auto detect this <code>usb0</code> interface, you will have to check it via <code>ping</code> or via Network Tools.

	For Ubuntu 11.04, just plug the USB cable in, with already-configured N900,the Network Manager will auto handle <code>usb0</code> interface.		<strong>For Ubuntu 11.04</strong>, just plug the USB cable in, with already-configured N900,the Network Manager will auto handle <code>usb0</code> interface.

	For 9.10 (NOT 10.04) you have to fix <code>/etc/init/network-interface.conf</code>, change the line:		<strong>For Ubuntu 9.10 (NOT 10.04)</strong> you have to fix <code>/etc/init/network-interface.conf</code>, change the line:
	stop on net-device-removed INTERFACE=$INTERFACE		stop on net-device-removed INTERFACE=$INTERFACE
	with:		with:
Line 295:		Line 298:
	(Note the difference: net-device-remove'''d''')		(Note the difference: net-device-remove'''d''')

	You have to reload udev rules with:		<strong>For all versions:</strong> You have to reload udev rules with:
	udevadm control --reload-rules		udevadm control --reload-rules

imported_>hongquan: /* Automatic configuration with Ubuntu 9.10/10.04/11.10 */

2011-11-29T16:45:28Z

Automatic configuration with Ubuntu 9.10/10.04/11.10

← Older revision		Revision as of 16:45, 29 November 2011
Line 284:		Line 284:
	</pre>		</pre>
	and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration".		and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration".

			The Network Manager on Ubuntu 11.10 won't auto detect this <code>usb0</code> interface, you will have to check it via <code>ping</code> or via Network Tools.

			For Ubuntu 11.04, just plug the USB cable in, with already-configured N900,the Network Manager will auto handle <code>usb0</code> interface.

	For 9.10 (NOT 10.04) you have to fix <code>/etc/init/network-interface.conf</code>, change the line:		For 9.10 (NOT 10.04) you have to fix <code>/etc/init/network-interface.conf</code>, change the line:

imported_>hongquan: /* Automatic configuration with Ubuntu 9.10/10.04/11.10 */

2011-11-29T16:40:20Z

Automatic configuration with Ubuntu 9.10/10.04/11.10

← Older revision		Revision as of 16:40, 29 November 2011
Line 280:		Line 280:

	For 11.10, put these lines to /etc/udev/rules.d/99-nokia-n900.rules		For 11.10, put these lines to /etc/udev/rules.d/99-nokia-n900.rules
			<pre>
	SUBSYSTEM=="net", ACTION=="add", ATTRS{idVendor}=="0421", ATTRS{idProduct}=="01c8", ATTRS{manufacturer}=="Nokia", ATTRS{product}=="N900 (PC-Suite Mode)", NAME="usb0", RUN+="/sbin/ifconfig usb0 192.168.2.14 up"		SUBSYSTEM=="net", ACTION=="add", ATTRS{idVendor}=="0421", ATTRS{idProduct}=="01c8", ATTRS{manufacturer}=="Nokia", ATTRS{product}=="N900 (PC-Suite Mode)", NAME="usb0", RUN+="/sbin/ifconfig usb0 192.168.2.14 up"
			</pre>
	and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration".		and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration".

imported_>hongquan: /* Automatic configuration with Ubuntu 9.10/10.04 */

2011-11-29T16:39:14Z

Automatic configuration with Ubuntu 9.10/10.04

← Older revision		Revision as of 16:39, 29 November 2011
Line 259:		Line 259:
	ifconfig n900		ifconfig n900

	=== Automatic configuration with Ubuntu 9.10/10.04 ===		=== Automatic configuration with Ubuntu 9.10/10.04/11.10 ===

	Note: this instructions should be fixed/improved:		Note: this instructions should be fixed/improved:
Line 278:		Line 278:
	down echo 0 > /proc/sys/net/ipv4/ip_forward		down echo 0 > /proc/sys/net/ipv4/ip_forward
	</pre>		</pre>

			For 11.10, put these lines to /etc/udev/rules.d/99-nokia-n900.rules
			SUBSYSTEM=="net", ACTION=="add", ATTRS{idVendor}=="0421", ATTRS{idProduct}=="01c8", ATTRS{manufacturer}=="Nokia", ATTRS{product}=="N900 (PC-Suite Mode)", NAME="usb0", RUN+="/sbin/ifconfig usb0 192.168.2.14 up"

			and don't modify <code>/etc/network/interfaces</code> in the way above, because you will make the boot slow with the message "waiting for network configuration".

	For 9.10 (NOT 10.04) you have to fix <code>/etc/init/network-interface.conf</code>, change the line:		For 9.10 (NOT 10.04) you have to fix <code>/etc/init/network-interface.conf</code>, change the line:

imported_>westwallpoma: /* N900 USB network configuration */

2011-11-01T18:15:53Z

N900 USB network configuration

← Older revision		Revision as of 18:15, 1 November 2011
Line 19:		Line 19:
	up route del default		up route del default
	up route add default gw 192.168.2.14		up route add default gw 192.168.2.14
			Also you can add the following lines to set the nameserver (dnsmasq will automatically change <code>/etc/resolve.conf</code>)
			dns-nameservers 8.8.8.8 8.8.4.4
	and		and
	up run-standalone.sh dbus-send --type=method_call --system --dest=com.nokia.icd /com/nokia/icd com.nokia.icd.connect string:DUMMY uint32:0		up run-standalone.sh dbus-send --type=method_call --system --dest=com.nokia.icd /com/nokia/icd com.nokia.icd.connect string:DUMMY uint32:0