LED Pattern Editor - Revision history

imported_>joerg_rw: /* Pattern engine commands */ what's PWM

2016-06-26T12:29:55Z

Pattern engine commands: what's PWM

← Older revision		Revision as of 12:29, 26 June 2016
Line 22:		Line 22:

	==== Pattern engine commands ====		==== Pattern engine commands ====
	Each of the two engines controls a single PWM output that can be used to drive any of the three LEDs in the notification light.		Each of the two engines controls a single PWM (Pulse Width Modulation, a way of dimming) output that can be used to drive any of the three LEDs in the notification light.
	* The ''Set PWM'' command sets the PWM output to the specified level (0-255).		* The ''Set PWM'' command sets the PWM output to the specified level (0-255).
	* The ''Ramp'' command increases or decreases the PWM output by the specified number of steps with a specified wait time after each step. The total duration of the ramp is the wait time multiplied by the number of steps plus one, (''wait_time'' * (''steps'' + 1)).		* The ''Ramp'' command increases or decreases the PWM output by the specified number of steps with a specified wait time after each step. The total duration of the ramp is the wait time multiplied by the number of steps plus one, (''wait_time'' * (''steps'' + 1)).

2.178.134.227: /* Restoring original patterns */

2012-05-23T23:05:48Z

Restoring original patterns

← Older revision		Revision as of 23:05, 23 May 2012
Line 47:		Line 47:
	[[Category:Software]]		[[Category:Software]]
	[[Category:Fremantle]]		[[Category:Fremantle]]

			----

imported_>andre: Undo revision 47526 by 2.178.139.136 (Talk)

2012-05-21T21:16:39Z

Undo revision 47526 by 2.178.139.136 (Talk)

← Older revision		Revision as of 21:16, 21 May 2012
Line 43:		Line 43:

	== Restoring original patterns ==		== Restoring original patterns ==
	During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore ~~origpattern editor: /home/user: Permission denied~~		During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore original patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.
	~~-sh: pattern: not found~~
	~~inal~~ patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.

	[[Category:		[[Category:Software]]

	Software]]
	[[Category:Fremantle]]		[[Category:Fremantle]]

2.178.139.136: /* Restoring original patterns */

2012-05-21T21:01:05Z

Restoring original patterns

← Older revision		Revision as of 21:01, 21 May 2012
Line 43:		Line 43:

	== Restoring original patterns ==		== Restoring original patterns ==
	During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore ~~original~~ patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.		During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore origpattern editor: /home/user: Permission denied
			-sh: pattern: not found
			inal patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.

	[[Category:Software]]		[[Category:

			Software]]
	[[Category:Fremantle]]		[[Category:Fremantle]]

imported_>speedevil at 00:08, 4 June 2010

2010-06-04T00:08:09Z

← Older revision		Revision as of 00:08, 4 June 2010
Line 1:		Line 1:
	A control panel applet to edit notification light blinking patterns. The [[Nokia N900\|N900]] has two configurable pattern engines ~~that interpret small programs (consisting of~~ up to 16 commands~~) and~~ can be ~~assigned~~ to ~~drive any~~ of the three (~~red~~, ~~green~~, ~~blue~~) ~~LEDs in~~ the notification light ~~with configurable brightness patterns via PWM~~. Details can be found on the [[LED patterns]] page.		A control panel applet to edit notification light blinking patterns.

			The [[Nokia N900\|N900]] has two configurable LED pattern engines.

			Each engine can be flexibly programmed with up to 16 commands to vary the brightness of the LEDs it is connected to.

			Either engine can be connected to one or more of the three LEDs (Red, Green, Blue) that make up the notification light.

			Details can be found on the [[LED patterns]] page.

	== Opening ==		== Opening ==

imported_>amigadave: slightly wikify, categorize

2010-06-01T10:44:08Z

slightly wikify, categorize

← Older revision		Revision as of 10:44, 1 June 2010
Line 1:		Line 1:
	A control panel applet to edit notification light blinking patterns. The N900 has two configurable pattern engines that interpret small programs (consisting of up to 16 commands) and can be assigned to drive any of the three (red, green, blue) LEDs in the notification light with configurable brightness patterns via PWM. Details can be found on the [[LED patterns]] page.		A control panel applet to edit notification light blinking patterns. The [[Nokia N900\|N900]] has two configurable pattern engines that interpret small programs (consisting of up to 16 commands) and can be assigned to drive any of the three (red, green, blue) LEDs in the notification light with configurable brightness patterns via PWM. Details can be found on the [[LED patterns]] page.

	=== Opening ===		== Opening ==
	To open the LED Pattern Editor, select ''Settings'' and ''LED Patterns''.		To open the LED Pattern Editor, select ''Settings'' and ''LED Patterns''.

Line 34:		Line 34:
	Selecting ''Done'' in the ''LED pattern editor'' dialog will save the changes to the pattern in the ''LED Patterns'' list. At this point, the changes are not yet applied. Just closing the ''LED Patterns'' dialog will revert any changes. Selecting ''Save'' will store the changes to the mce configuration file after a warning and restart the mce process.		Selecting ''Done'' in the ''LED pattern editor'' dialog will save the changes to the pattern in the ''LED Patterns'' list. At this point, the changes are not yet applied. Just closing the ''LED Patterns'' dialog will revert any changes. Selecting ''Save'' will store the changes to the mce configuration file after a warning and restart the mce process.

	=== Restoring original patterns ===		== Restoring original patterns ==
	During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore original patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.		During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore original patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.

			[[Category:Software]]
			[[Category:Fremantle]]

imported_>ph5: New page: A control panel applet to edit notification light blinking patterns. The N900 has two configurable pattern engines that interpret small programs (consisting of up to 16 commands) and can b...

2010-05-27T20:30:40Z

New page: A control panel applet to edit notification light blinking patterns. The N900 has two configurable pattern engines that interpret small programs (consisting of up to 16 commands) and can b...

New page

A control panel applet to edit notification light blinking patterns. The N900 has two configurable pattern engines that interpret small programs (consisting of up to 16 commands) and can be assigned to drive any of the three (red, green, blue) LEDs in the notification light with configurable brightness patterns via PWM. Details can be found on the [[LED patterns]] page.

=== Opening ===
To open the LED Pattern Editor, select ''Settings'' and ''LED Patterns''.

=== Viewing patterns ===
The ''LED Patterns'' dialog shows the list of defined patterns with a graphical representation of the LED brightness over time. Each vertical line corresponds to one second.

=== Editing patterns ===
Clicking on a pattern button opens the ''LED pattern editor'' dialog. Below the graphical pattern view, there is a list of commands that will be interpreted by the currently selected engine. Engine 1 or 2 can be selected by the toggle button to the right, below the color chooser buttons which assign the LEDs to drive to each of the engines.
* To edit a command in the currently selected engine's program, tap the command button in the list. Change the command's parameters in the command edit dialog and observe the changes in the graphical pattern view. Select ''Done'' when finished or close the dialog to revert the changes.
* Select ''Delete'' to remove the command from the list.
To add a new command, tap the ''New command'' button at the end of the list.

==== Pattern engine commands ====
Each of the two engines controls a single PWM output that can be used to drive any of the three LEDs in the notification light.
* The ''Set PWM'' command sets the PWM output to the specified level (0-255).
* The ''Ramp'' command increases or decreases the PWM output by the specified number of steps with a specified wait time after each step. The total duration of the ramp is the wait time multiplied by the number of steps plus one, (''wait_time'' * (''steps'' + 1)).
* The ''Wait'' command is the same as a ''Ramp'' with zero steps. The duration is equal to the wait time.
* A ''Trigger'' command is used to wait for a trigger from the other engine or to set a trigger to the other engine to release it from a waiting state. This command can be used to synchronize the two independently running engines.
* The ''Go To Start'' command is used to repeat the pattern from the first step. All patterns must end in a ''Go To Start'' or ''End'' command.
* The ''End'' command stops the engine, ending the program. It can be configured to either ''Hold'' the PWM level at the current value indefinitely or to ''Reset'' the PWM level to 0, turning off the connected LEDs.

=== Copy & paste ===
Patterns can be copied to and pasted from the clipboard in the [[LED patterns#Pattern Format|format described here]].
* The ''Copy'' button (or the keyboard shortcut '''Ctrl+c''') copy the current pattern to the clipboard.
* To paste a pattern from the clipboard, use the keyboard shortcut '''Ctrl+v'''.
See [[LED patterns#Community-Made Patterns|Community-Made Patterns]] for some examples.

=== Testing patterns ===
The ''Test'' button will start to replay the current pattern if it is well-formed. Unfortunately, the mce process will stop the playback occasionally and uncontrollably.

=== Saving changes ===
Selecting ''Done'' in the ''LED pattern editor'' dialog will save the changes to the pattern in the ''LED Patterns'' list. At this point, the changes are not yet applied. Just closing the ''LED Patterns'' dialog will revert any changes. Selecting ''Save'' will store the changes to the mce configuration file after a warning and restart the mce process.

=== Restoring original patterns ===
During the first installation, the LED Pattern Editor package stores a backup copy of the mce configuration file. Selecting ''Restore original patterns'' will restore the LED patterns from that file, overwriting all user-created patterns.